PAC AOEM-FRD2 Ford Premium Sound System Interface
$ 53.99 $ 44.95
The PAC AOEM-FRD2 Sound System Interface is a "specific application" Kit of the PAC OEM-1 interface. It allows for the replacement or addition of an amplifier in compatible vehicles with a premium sound system.
Do you have a Premium factory sound system? If so, with this kit, you can easily:
- Replace the factory amplifier(s) and keep the factory stereo or
- Keep all of the factory system and add amplifiers (up to 4 channels)
This AOEM Kit includes:
- (1) PAC OEM-1 main unit
- (1) AMP-RCA harness
- (1) ADD-FRD2 harness
The OEM-1 interface is transformer isolated, maintains phase and is linear from 20 to 20,000 Hz. This 4-channel interface will allow the output to be adjusted to the input requirements of the new amplifier, providing 2:1 gain and infinite attenuation. The input connectors plug into the factory stereo and vehicle harness. The 4 female RCA output jacks plug into the new amplifier. Comes complete with amplifier trigger wire. Just like the factory stereo system, the warning chimes will play through the front left RCA output of the interface. Also, turning on the rear entertainment controls, if so equipped, will make the rear outputs of the interface play a second audio source.
Everything just plugs together (Plug & Play). When you want to take out whatever you added or
changed, just unplug it and plug in the old factory stuff. The vehicle is back
to factory condition. You can use the amplifier you added
in your next leased or purchased vehicle.
The OEM-1 also gives you 2:1 gain as well as infinite attenuation. This allows signal adjustment to the correct level between the factory system and what is being added or changed. All four channels are individually adjusted for accurate sound levels. Each channel completely isolates the aftermarket equipment from the factory system to give 100% compatibility in every installation.
"plug and play" solution - no need to cut wires
- Provides a 4 channel RCA output when adding an additional amplifier
- Signal ground is also isolated to avoid ground loops
- 4 channel, transformer isolated and adjustable Line Output Converter
- All four channels are individually adjusted
- Linear from 20-20,000 Hz (+/- 0.5dB)
- Maintains correct phase
To replace the premium factory amplifier:
ADD cable plugs into the factory harness and into the OEM-1. The second cable is the AMP-RCA. This cable plugs into the OEM-1 and has 4 channels of RCA output (using RCA jacks) and the trigger lead needed to turn on the amplifier(s). Run RCA leads and trigger extension to amplifier from the AMP-RCA. Run main amplifier power directly from battery. Connect speaker outputs of amplifier to factory or aftermarket speakers. Adjust the potentiometers on the OEM-1 and the installation is complete.
To add an amplifier to the premium factory system:
You can leave the premium factory system in place and add up to 4 channels of amplification with simple plug ins. ADD cable plugs into the existing factory harness and the OEM-1. The second cable is the AMP-RCA. As above it plugs into the OEM-1 and has 4 channels of RCA output and the trigger lead needed to turn on the amplifier(s). Run RCA leads and trigger extension to amplifier from the AMP-RCA. Run main amplifier power directly from battery. Connect speaker outputs of amplifier to factory or aftermarket speakers. Adjust the potentiometers on the OEM-1 and the installation is complete.
Click here to see the most current application guide
NOTE: If you do not see your vehicle listed below or need assistance getting the right product, call PAC Technical Support at (800) 854-3133 to find out which PAC product is right for your vehicle.
Ford All Ford JBL system 1989-1995 (Stereos with no antenna plugged into it
are not supported)
Ford All JBL & Mach Systems 1996-1998 (except Ford Mustang Mach System)